Technical Support

How to use:

Apply approximately 8 drops of AQUA Coating ONE to a dry foam applicator (for this coating we don't use suede cloth!!!). This amount is enough to cover about half of a medium-sized bodywork element. the applied coating layer should be thick and wet (an already soaked applicator means that fewer drops may be needed for further application). 

Spread the coating on the varnish using crisscross movements.

After waiting about 1 minute, remove excess product with the first microfiber (the product crystallizes quickly, so do not wait too long). Use the second microfiber to polish the surface until shiny.

After applying the coating to all vehicle components, leave them in favorable weather conditions for 24 hours. Make sure the temperature does not drop below 10 degrees Celsius. 

For best results, we recommend applying two coats of AQUA Coating ONE, not one. Be sure to apply Coating Booster 10 hours after applying the final coat of AQUA Coating ONE.

To prepare the vehicle for coating, clean the paint (de-ironization, decontamination + claying), safely and thoroughly wash the surface, perform mechanical paint correction and degrease the bodywork (preferably twice). 

Important additional information:

1. Remember that the coating applied at temperatures above 20 degrees dries faster, so divide large elements, such as a mask, into two parts. 

2. Ensure good lighting when applying the coating.

3. Protect the surface from moisture for 24 hours after application.

4. For the first 7 days, the coating must not be exposed to unfavorable weather conditions.

5. Never use the product on a hot or damp surface.

6. Do not apply AQUA Coating ONE in the rain or in direct sunlight.

7. Do not let the temperature drop below 10 degrees.

8. Use the dedicated AQUA applicator to ensure proper coating application.

9. Use appropriate personal protective equipment during application.

10. Wash your coated car by hand at least every two weeks.

Attention – important information!

Tym, co w największym stopniu wpłynąć może na zniszczenie świeżej, niedostatecznie jeszcze utwardzonej powłoki, jest brud !  który się do niej przedostaje. Co za tym idzie, przez dwa tygodnie od aplikacji (czyli przez okres, w którym zachodzi proces utwardzania powłoki) klient powinien zwracać baczną uwagę na to, by swojego samochodu nadmiernie nie zabrudzić. I teraz najważniejsze: jeśli do takiego zabrudzenia już doszło, to umycie powierzchni jakimś neutralnym środkiem będzie o wiele mniej szkodliwe dla powłoki, niż pozostawienie na niej zabrudzeń. 

How to use:

Na suchy aplikator nałóż około 8 kropli AQUA Coating 9H. Taka ilość jest wystarczająca do tego, by pokryć nią około połowy elementu karoserii średniej wielkości (nasączony już aplikator sprawia, że przy dalszej aplikacji może być potrzebna mniejsza liczba kropel). Powłokę rozprowadzaj na lakierze wykonując ruchy krzyżowe. Po odczekaniu około 30-60 sekund usuń nadmiar produktu przy pomocy pierwszej mikrofibry (produkt szybko się krystalizuje, dlatego nie czekaj zbyt długo). Drugą mikrofibrą wypoleruj powierzchnię do uzyskania połysku. Po naniesieniu powłoki na wszystkie elementy auta pozostaw je w sprzyjających warunkach atmosferycznych na 24 godziny. Zadbaj, by temperatura nie spadła poniżej 10 stopni. Dla osiągnięcia najlepszego efektu zalecamy nałożenie nie jednej, ale dwóch warstw powłoki AQUA Coating 9H. Koniecznie 10 godz. po aplikacji ostatniej warstwy AQUA Coating PRO 9H zaaplikuj Coating Booster !!!

To prepare the vehicle for coating, clean the paintwork (de-ironization, decontamination + claying), safely and thoroughly wash the surface, mechanically correct the paintwork and degrease the bodywork (preferably twice).

Important additional information: Remember that the applied coating dries very quickly, so divide large elements, such as a mask, into two parts. Ensure good lighting when applying the coating.

Protect the surface from moisture for 24 hours after application. The coating should not be exposed to adverse weather conditions for the first 7 days.

Never use the product on a hot or damp surface.

Do not apply AQUA Coating 9H in the rain or in direct sunlight.

Don't let the temperature drop below 10 degrees Celsius. Use a dedicated AQUA applicator to ensure proper coating application.

Use appropriate personal protective equipment during application. Hand wash your coated car at least every two weeks.

Attention – important information! Tym, co w największym stopniu wpłynąć może na zniszczenie świeżej, niedostatecznie jeszcze utwardzonej powłoki, jest brud ! który się do niej przedostaje. Co za tym idzie, przez dwa tygodnie od aplikacji (czyli przez okres, w którym zachodzi proces utwardzania powłoki) klient powinien zwracać baczną uwagę na to, by swojego samochodu nadmiernie nie zabrudzić. I teraz najważniejsze: jeśli do takiego zabrudzenia już doszło, to umycie powierzchni jakimś neutralnym środkiem będzie o wiele mniej szkodliwe dla powłoki, niż pozostawienie na niej zabrudzeń.

   Application method:  

• Ensure ideal conditions – the air temperature during application of the coating should be around 15-20 degrees Celsius.
• Thoroughly clean the glass surface of all types of dirt, 90% of the durability of the product depends on the surface preparation.
• Apply a few drops of the preparation to a dry applicator.
• Apply the first layer using vertical movements, without skipping any spots. Once finished, immediately apply a second layer using horizontal movements. This way, you'll be sure to cover the entire glass perfectly. When you see the applicator becoming dry, add a few drops. 
• Leave the preparation to dry completely (usually about 15 minutes at 18 degrees Celsius is enough, but you can also leave it overnight).
• Remove excess preparation with AQUA microfiber (rub in without pressure, using circular movements).
• Polish the protected surface with a second, dry AQUA microfiber.

Important! Your vehicle must not be exposed to adverse weather conditions for at least 12 hours after application.

Prepare the glass surface in the same way as the varnish, i.e. chemically remove mineral dirt, then polish and degrease the surface.

How to use:

• Before applying the coating, thoroughly clean the surface to be protected and degrease it twice (isopropyl alcohol can be used)
• It is best to apply the coating in straight lines directly to the surface using an applicator or a special coating cloth.
• After waiting 1 minute, polish the cleaned surface using a dry microfiber cloth.

Attention: AQUA Wheel Coating should not be applied in full sunlight, at temperatures below 10 degrees Celsius or on hot elements.

How to use:

• Spray the preparation on the glass surface to be cleaned.
• Clean the surface with a microfiber cloth (short-bristled).
• Polish the surface with a second, dry and clean microfiber cloth.
• Repeat the operation if necessary.

How to use:

• Spray the preparation on the glass surface to be cleaned.
• Clean the surface with a microfiber cloth (short-bristled).
• Polish the surface with a second, dry and clean microfiber cloth.
• Repeat the operation if necessary.

How to use:

• Open the product and apply a few drops of the coating to an unused suede microfiber (from AQUA).
• Select any vehicle element, such as the hood, and begin rubbing the coating in. Apply the coating using a crisscross pattern (horizontal and vertical movements). It's a good idea to divide large elements like the hood or roof into several sections.
• Spread the coating again in the same place, using only the applicator without adding any product.
• Wait 15-30 seconds depending on application conditions.
• Remove excess coating with the first unused AQUA microfiber.
• Buff the paintwork to a streak-free shine using a second unused microfiber cloth.

Comments:  

Preparation:

For both new and used vehicles, we recommend machine paint correction, depending on the paint's wear. The final step is to degrease the paint with isopropyl alcohol.

Application during the period spring-summer:

1. Open the product and apply a few drops of coating to the applicator (without the suede cloth).

2. Select any part of the vehicle, e.g. the hood, and start rubbing the coating. Apply the coating using a crisscross pattern, applying a wet layer (horizontal and vertical movements). Larger elements like the hood or roof should be divided into several sections.

3. Spread the coating again in the same place, using only the applicator without adding any product.

4. After application, start lapping the coating immediately.

5. Remove excess coating with the first unused AQUA microfiber.

6. Buff the paintwork to a streak-free shine using a second unused microfiber cloth.

Application in autumn and winter:

1. Open the product and apply a few drops of the coating to an unused suede microfiber (from AQUA).

2. Select any vehicle element, such as the hood, and begin rubbing the coating in. Apply the coating using a crisscross pattern (horizontal and vertical movements). It's a good idea to divide large elements like the hood or roof into several sections.

3. Spread the coating again in the same place, using only the applicator without adding any product.

4. Wait 15-30 seconds depending on application conditions.

5. Remove excess coating with the first unused AQUA microfiber.

6. Buff the paintwork to a streak-free shine using a second unused microfiber cloth.